Home Contact EN

Blogs & Insights

Find out the latest innovations from ActionPower

Published on: Updated on: Author: Zhiwei Bao Reviewed: Sen Wang

Testing Switching Power Supply with Programmable Electronic Loads: Applications and Setup Guide




Modern electronic components, devices, and systems ultimately derive their power supply from the local utility grid, where AC power is converted through a series of complex stages into the required DC voltage levels for operation. Power conversion systems, such as AC-DC converters and switched-mode power supplies (including DC-DC converters), serve to scale, regulate, and adapt the grid power into the specific voltage and current levels demanded by the load.

A typical example is the DIN Rail power supplies by MeanWell which are commonly used for sourcing power to those low-voltage electrical like PLC within the cabinet of industrial equipment like automation systems and manufacturing equipment. SMPSs are supposed to provide reliable, efficient, and stable DC output corresponding to that that loads dictate, for example, DC 24V for programmable logic controller.

Validating your switched-mode power supplies (SMPSs) with ActionPower’s electronic loads offers unparalleled advantages in terms of flexibility, dynamics, and precision. The PCL DC Electronic Load is our highlighted solution, featuring power scalability up to 600 kW and an ultra-fast 20 μs rise time. Its dynamic testing capabilities, with a modulation bandwidth of up to 20 kHz, make it an ideal choice for accurately measuring rise/fall time, transient response, and stability of SMPSs.


Basics of Switched-Mode Power Supplies

As backbone of modern electronics that powering devices all across industries including consumer products, automotive systems, communication equipment and industrial automation, switched-mode power supplies are supposed to undergo rigorous validation under different load conditions so that they are qualified to source ranges of loads with safety and stability.

Switched-mode power supply converts a DC input voltage into a different one in correspondence to the certain topology used within its circuit that may be built in three classifications according to their conversion functions, which are step-down (buck), step-up (boost), and step-up/down (buck-boost or inverter).

buck circuit
Buck Circuit Topology
boost circuit
Boost Circuit Topology
buck-boost circuit
Buck-Boost Circuit Topology

Role of Programmable Electronic Loads in SMPS Testing

Electronic loads, in contrast to SMPSs that supply power to connected loads, are devices designed to sink power from a source. E-loads provide precise and programmable control of this sinking behaviour, enabled by control software and closed-loop circuitry built around high-power semiconductor devices such as MOSFETs or IGBTs. Through this architecture, programmable electronic loads are able to accurately emulate a wide variety of load conditions applied to an SMPS.

Programmable Electronic Loads is configurable to operate in CC, CV, CR or CP mode or a combination of them so that the specific parameter fro the source and input is maintained at a certain target level thus to emulate real-world loads’ characteristics  – Click here to read the more about the technical fundamental of E-Loads
Electronic Load Operation Modes Explained: How Does its Circuit Regulate Input Current, Voltage and Resistance?

E-Load Applications for Primary SMPSs Test Cases Explained

Fast response, high power capability, and flexible control logics are highlighted fundamental characteristics that allow electronic loads to verify the reaction and operation capability of power sources against either transient and dynamic or static status. Setting up the testing environment involves as well an oscilloscope to form a platform for repeatable and measurable testing execution.

Testing topology setup of power supply with electronic load

The below shows those primary testing cases you may take advantages of programmable electronic loads against your power supply:

basic-performance-tests

Basic Performance

dynamic-response-tests

Dynamic Response

protection-and-limit-test

Protection and Limit

stability-and-ripple-measurement-test

Ripple and Stability

Basic Performance Tests

Verify SMPS’s stability in voltage output against different loading conditions, as well as how efficiently it holds voltage when line regulation varies and current changes (load regulation)

Dynamic Response Tests

Dynamics response capability includes how fast the power supply reacts to voltage ramp-up and drops when it is turned off, then how rapidly it switches between different current levels, monitored by oscilloscope which captures overshoot, undershoot, and recovery time of the output voltage.

Protection and Limit Verification

Verification of SMPS’s Over-Current Protection (OCP), Short-Circuit Protection (SCP) and Over-Power Protection (OPP) by setting the electronic loads in various working mode including CC, CP or forcing near-zero resistance to simulate short circuit.

Stability and Ripple Measurements

Thermal stability and endurance verification over constant or cycle loading over extended period. And ripple voltage and high-frequency noise validation at rated load.

Transient Response Time Test with E-Load Configured in Dynamic Load

Power supplies are supposed to source stable voltage level, while real-world load regulation may face changing and unstable current status.

Though the feedback control circuit has already taken in to consideration the essential capability of continuously maintaining the output voltage stable, the bandwidth inherently limits how fast the circuit reacts to current changes. Programmable electronic loads serve here as the equipment to simulate the worst current load conditions that the power supply may have to handle in actual operation.

Engineer can set up the PCL Electronic Load in dynamic mode to test the transient response of the power supply. Loading stepping changes provided PCL electronic loads allows the verification of power supply from no-load to full-load status meanwhile to observe both the voltage waveform changes and response time through the oscilloscope.

Voltage Rise/Drop Time Test of Switching Power Supply

Power supplies are required to meet different drop and rise time standards when they are used in different industries and devices. One of the examples is when power supplies is used for PC, where it is supposed to hold up the voltage or at least the voltage drop time should not be too short that the data storage will fail upon unexpected system shut down due to power failure.

For LED driver power supplies, the design requirement for voltage drop behaviour is fundamentally different from that of PC power supplies. Unlike a PC, which needs to maintain or slow down the voltage fall to ensure data integrity during sudden power loss, an LED driver has no such data-retention requirement. If the output voltage decays too slowly, the LED will operate in a low-voltage region where the current is unstable. This causes flickering, dimming, or irregular brightness transitions, which negatively affect the user experience.

pcl elctronic load voltage sag test of power supply

Reach ActionPower for Learning More of Our Technical Advantages

No matter for what kind of devices your power supplies are expected to source power, ActionPower’s programmable electronic loads are at your option to support your testing, validation and inspection from research and development to testing and final production end-of-line. With our dedication to power electronics and industrial testing for decades, ActionPower’s electronic loads have been trusted by industrial leaders in the field of electrical and electronic industries to facilitate their development and production.

For further inquiries about your SMPSs testing projects, feel free to get in contact with our team by sending emails or submitting a contact form.

 

 


ActionPower research and development team

Talk to ActionPower

From ActionPower we are open to listening to your suggestions and opinions.

For further media contact or consultation about any topics which might be of your interest about our company, you will be welcomed to send us an email to:

info@actionpowertest.com

Latest News


PRL DC Load Simulator Introduced by ActionPower for AI Server Workload Validation

Dynamics and power regeneration are no longer compromise to each other. Adopting innovation topology technologies is the PRL DC Load Simulator that accommodates ultra-fast dynamics, regenerative load and high-power scalability from a united single system.



ActionPower to Debut MIX Series Hybrid Power Supply at Europe Automotive Testing Expo 2025

The latest hybrid programmable power supply by ActionPower comes with 6 channels hybrid interface and allows AC/DC module arbitrary combination for flexible testing configuration where both AC and DC are...



CONTANCT US

Zhiwei Bao, SEO Engineer and technical copywriter at ActionPower
About the Author

Zhiwei Bao

Industrial Automation Power Electronics Product Marketing Field Application

Zhiwei Bao holds 20+ patents in the field of mechanical engineering and is keen on industrial automation and product marketing. His interdisciplinary background, along with his passion and initiative for learning, has led him to a profound understanding of power electronics. He manages the technical copywriting for programmable power and testing topics at ActionPower through product-marketing-driven approaches.

About Zhiwei Bao

Explore More

diesel generator and data center for AI facility

The Surge in AI data Center Construction is the Boom in Industrial...

Figures of Soaring AI Data Center Construction Following AI Boom Public available data shows the investment to data center construction...



Why Linear Loads Demonstrates Better Dynamics Performance than Regenerative Ones? And How ActionPower Breaks the Boundary?

Why Linear Loads Demonstrates Better Dynamics Performance than Regenerative Ones? And How...

Conventional testing applications where programmable electronic loads are deployed used to see a definite trade-off between dynamic performance and the...



combination of software and hardware is battery cycler's key feature

Grid Code Compliance Test Explained: What to Validate and Which Standards to...

Facing the modern grid landscape is the ever more important grid interconnection and interoperability, since DERs are now enacting as...




Get in Contact

Global Contact

Sales Network & Locations

If you are looking for an automated test system to validate your products during development and research stages to make sure of their successful commercial launch, ACTIONPOWER will be at your disposal to study your specifications and requirements to provided either standard or customized testing solutions.

Product Inquiry

Specification-matching testing and simulation solutions need discussion of both parties. Actionpower welcomes you inquirt to study together with us about how we can automate your testing processes.

Send Inquiry

Trade Shows & Events

These are the upcoming events and places you can find ACTIONPOWER and talk with us face-to-face!

Check Events

Social Media

Follow us to keep updated of our innovations.

LinkedInTwitter
Quick Model Access

Smart Discovery

Access our Power Supply Wizard to find the right programmable power supply for your use cases and testing scenarios.

discover programmable power supply by filtering with current, voltage and power ranges
CONTACT US

Contact Us

Professionalism is what we care about. Why not email us with your technical requirements fully explained rather than submitting a simple message so that we revert more proactively with detailed solutions?

Subscribe to Newsletter

Thank you for subscribing!